GATEWAY0="192.168.1.1"
DNS1="192.168.1.1"
IPV6_PEERDNS="yes"
IPV6_PEERROUTES="yes"
如你所见，我已经加了两个IP地址：IPADDR1=”192.168.1.151″ & IPADDR2=”192.168.1.152″
类似地，你可以加入更多的ip地址。
最后，保存并退出文件。重启网络服务来使更改生效。
复制代码systemctl restart network
现在，让我们检查是否已经加入了ip地址。
复制代码ip addr
示例输出：
复制代码 : lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 08:00:27:3f:ab:68 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.150/24 brd 192.168.1.255 scope global enp0s3
valid_lft forever preferred_lft forever
inet 192.168.1.151/24 brd 192.168.1.255 scope global secondary enp0s3
valid_lft forever preferred_lft forever
inet 192.168.1.152/24 brd 192.168.1.255 scope global secondary enp0s3
valid_lft forever preferred_lft forever
inet6 fe80::a00:27ff:fe3f:ab68/64 scope link
valid_lft forever preferred_lft forever
如你所见，单个网卡已经有3个ip地址了。
让我们ping一下新增的IP地址：
复制代码ping -c 4 192.168.1.151
示例输出：
复制代码 PING 192.168.1.151 (192.168.1.151) 56(84) bytes of data.
64 bytes from 192.168.1.151: icmp_seq=1 ttl=64 time=0.048 ms
64 bytes from 192.168.1.151: icmp_seq=2 ttl=64 time=0.075 ms
64 bytes from 192.168.1.151: icmp_seq=3 ttl=64 time=0.077 ms
64 bytes from 192.168.1.151: icmp_seq=4 ttl=64 time=0.077 ms
--- 192.168.1.151 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 2999ms
rtt min/avg/max/mdev = 0.048/0.069/0.077/0.013 ms</p>
<p> ping -c 4 192.168.1.152
示例输出：
复制代码PING 192.168.1.152 (192.168.1.152) 56(84) bytes of data.
64 bytes from 192.168.1.152: icmp_seq=1 ttl=64 time=0.034 ms
64 bytes from 192.168.1.152: icmp_seq=2 ttl=64 time=0.075 ms
64 bytes from 192.168.1.152: icmp_seq=3 ttl=64 time=0.073 ms
64 bytes from 192.168.1.152: icmp_seq=4 ttl=64 time=0.075 ms
--- 192.168.1.152 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 2999ms
