本篇文章详细的讲诉了nginx服务器中的安全配置，具体如下：
一、关闭SELinux
安全增强型Linux（SELinux）的是一个Linux内核的功能，它提供支持访问控制的安全政策保护机制。
但是，SELinux带来的附加安全性和使用复杂性上不成比例，性价比不高
sed -i /SELINUX=enforcing/SELINUX=disabled/ /etc/selinux/config /usr/sbin/sestatus -v #查看状态
二、通过分区挂载允许最少特权
服务器上 nginx 目录单独分区。例如，新建一个分区/dev/sda5(第一逻辑分区)，并且挂载在/nginx。确保 /nginx是以noexec, nodev and nosetuid的权限挂载
以下是我的/etc/fstab的挂载/nginx的信息：LABEL=/nginx /nginx ext3 defaults,nosuid,noexec,nodev 1 2
注意：你需要使用fdisk和mkfs.ext3命令创建一个新分区。
三、配置/etc/sysctl.conf强化Linux安全
你可以通过编辑/etc/sysctl.conf来控制和配置Linux内核、网络设置
# Avoid a smurf attack net.ipv4.icmp_echo_ignore_broadcasts = 1 # Turn on protection for bad icmp error messages net.ipv4.icmp_ignore_bogus_error_responses = 1 # Turn on syncookies for SYN flood attack protection net.ipv4.tcp_syncookies = 1 # Turn on and log spoofed, source routed, and redirect packets net.ipv4.conf.all.log_martians = 1 net.ipv4.conf.default.log_martians = 1 # No source routed packets here net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.default.accept_source_route = 0 # Turn on reverse path filtering net.ipv4.conf.all.rp_filter = 1 net.ipv4.conf.default.rp_filter = 1 # Make sure no one can alter the routing tables net.ipv4.conf.all.accept_redirects = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv4.conf.all.secure_redirects = 0 net.ipv4.conf.default.secure_redirects = 0 # Don't act as a router net.ipv4.ip_forward = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.default.send_redirects = 0 # Turn on execshild kernel.exec-shield = 1 kernel.randomize_va_space = 1 # Tuen IPv6 net.ipv6.conf.default.router_solicitations = 0 net.ipv6.conf.default.accept_ra_rtr_pref = 0 net.ipv6.conf.default.accept_ra_pinfo = 0 net.ipv6.conf.default.accept_ra_defrtr = 0 net.ipv6.conf.default.autoconf = 0 net.ipv6.conf.default.dad_transmits = 0 net.ipv6.conf.default.max_addresses = 1 # Optimization for port usefor LBs # Increase system file descriptor limit fs.file-max = 65535 # Allow for more PIDs (to reduce rollover problems); may break some programs 32768 kernel.pid_max = 65536 # Increase system IP port limits net.ipv4.ip_local_port_range = 2000 65000 # Increase TCP max buffer size setable using setsockopt() net.ipv4.tcp_rmem = 4096 87380 8388608 net.ipv4.tcp_wmem = 4096 87380 8388608 # Increase Linux auto tuning TCP buffer limits # min, default, and max number of bytes to use # set max to at least 4MB, or higher if you use very high BDP paths # Tcp Windows etc net.core.rmem_max = 8388608 net.core.wmem_max = 8388608 net.core.netdev_max_backlog = 5000 net.ipv4.tcp_window_scaling = 1
